آمار
| تعداد نشریات | 31 |
| تعداد شمارهها | 1,029 |
| تعداد مقالات | 9,100 |
| تعداد مشاهده مقاله | 10,289,978 |
| تعداد دریافت فایل اصل مقاله | 8,526,167 |
Pre-drilling Effect on Thermal Friction Drilling of Cast Aluminum Alloy Using Thermo-mechanical Finite Element Analysis | ||
| Journal of Applied and Computational Mechanics | ||
| دوره 6، Special Issue، اسفند 2020، صفحه 1371-1379 اصل مقاله (1.41 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22055/jacm.2020.34682.2455 | ||
| نویسنده | ||
| Sara Ahmed El-Bahloul* | ||
| Production & Mechanical Design Engineering Department, Faculty of Engineering, Mansoura University, Mansoura, 35511, Egypt | ||
| چکیده | ||
| Thermal friction drilling is a non-conventional hole making process, which uses a rotating tool to penetrate the workpiece and create a bushing. Friction drilling of brittle cast alloys is likely to result in severe petal forming and radial fracturing. This research investigates the effect of pre-drilling diameter and depth on the produced bushing cracks and petal formations while drilling cast aluminum alloy (A380). A three-dimensional finite element model of high-temperature deformation and large plastic strain is performed by using ABAQUS software. Modeling by using dynamic, temperature-displacement, explicit, as well as the adaptive meshing, element deletion, interior contact, and mass scaling techniques, is necessary to enable the convergence of the solution. The finite element analysis results predict that the pre-drilling has a significant effect on the produced bushing shape. The effect of initial deformation decreases with pre-drilling, leading to fewer cracks and petal formations. Hence, the obtained bushing length increases, so providing a more load-bearing surface that leads to a stiffer joint. Additionally, the effect of pre-drilling on the produced temperature is studied, and the results reveal that by increasing the pre-drilling diameter or depth the temperature decreases. Therefore, less workpiece material melting occurs, which leads to less adhering on the tool surface, so fewer cracks and petal formations. | ||
| کلیدواژهها | ||
| Thermal friction drilling؛ Cast aluminum alloy؛ Finite element analysis؛ Pre-drilling؛ Bushing length؛ Temperature | ||
| مراجع | ||
|
[1] G. Urbikain, J. M. Perez, L. N. Lopez de Lacalle, and A. Andueza, Combination of friction drilling and form tapping processes on dissimilar materials for making nutless joints, Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., 232(6), 2018, 1007-1020. [2] C. A. Muñoz-Ibáñez, M. Alfaro-Ponce, G. Perez-Lechuga, and J. A. Pescador-Rojas, Design and Application of a Quantitative Forecast Model for Determination of the Properties of Aluminum Alloys Used in Die Casting, Int. J. Met., 13(1), 2019, 98–111. [3] S. F. Miller, J. Tao, and A. J. Shih, Friction drilling of cast metals, Int. J. Mach. Tools Manuf., 46(12–13), 2006, 1526–1535. [4] S. F. Miller and A. J. Shih, Thermo-Mechanical Finite Element Modeling of the Friction Drilling Process, J. Manuf. Sci. Eng., 129(3), 2007, 531. [5] Z. Demir and C. Özek, Investigate the effect of pre-drilling in friction drilling of A7075-T651, Mater. Manuf. Process., 29(5), 2014, 593–599. [6] Z. Demir, An Experimental Investigation of the Effect of Depth and Diameter of Pre-drilling on Friction Drilling of A7075-T651 Alloy, J. Sustain. Constr. Mater. Technol., 1(2), 2016, 46–56. [7] M. B. Bilgin, K. Gök, and A. Gök, Three-dimensional finite element model of friction drilling process in hot forming processes, Proc. Inst. Mech. Eng. Part E J. Process Mech. Eng., 231(3), 2017, 548–554. [8] R. Kumar and N. R. J. Hynes, Finite-element simulation and validation of material flow in thermal drilling process, J. Brazilian Soc. Mech. Sci. Eng., 40(3), 2018, 1–10. [9] E. Oezkaya, S. Hannich, and D. Biermann, Development of a three-dimensional finite element method simulation model to predict modified flow drilling tool performance, Int. J. Mater. Form., 12(3), 2019, 477–490. [10] S. A. El-Bahloul, Friction Drilling of Cast Aluminum Alloy A380 Without Significant Petal Formation and Radial Fracture, Int. J. Precis. Eng. Manuf., 20(1), 2019, 45–52. [11] S. Dehghan, E. Souri, and others, A thermo-mechanical finite element simulation model to analyze bushing formation and drilling tool for friction drilling of difficult-to-machine materials, J. Manuf. Process., 57, 2020, 1004–1018. [12] S. A. El-Bahloul, H. E. El-Shourbagy, A. M. El-Bahloul, and T. T. El-Midany, Experimental and Thermo-Mechanical Modeling Optimization of Thermal Friction Drilling for AISI 304 Stainless steel, CIRP J. Manuf. Sci. Technol., 20, 2018, 84–92. [13] S. Gupta, S. Abotula, and A. Shukla, Determination of johnson-cook parameters for cast aluminum alloys, J. Eng. Mater. Technol. Trans. ASME, 136(3), 2014, 034502. | ||
|
آمار تعداد مشاهده مقاله: 548 تعداد دریافت فایل اصل مقاله: 609 |
||